F-KB090 Carbonized bamboo knife seat，your best choice

Ref Price:

Loading Port:: Guangzhou

Payment Terms:: TT OR LC

Min Order Qty:: 1000 pc

Supply Capability:: 100000 pc/month

Inquire Now

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Kitchen Knife Set-05

Non-Stick Colorful Knife Set

Polycarbonate Greenhousewith Aluminum Fram

F-KB037 Rubber wood knife seat，your best choice

F-KB094 Carbonized bamboo knife seat，your best choice

knife seat,F-KB012 acacia wood knife seat，your best choice

Diamond Whetstone Double Sides Knife Sharpening Stone with Holder

Diamond Sharpening Stones 400#1000# Double Sides Whetstone of Top Quality

product name：rubber wood knife seat

material：Carbonized bamboo

N.W.：0.486kg

MEAS：14*16*8cm

Product advantage：

How does the bamboo product carbonize？Firstly，put the bamboo or bamboo bag into the high-pressure carbonized boiler of 200 degrees - 300 degrees for vapor carbonization.

And after high temperature and high pressure, so that form a hard carbide particles layer on the surface.At the same time,the bamboo itself will be more harder.

The advantage of carbonized bamboo knife seat:after carbonize,hard carbide particles will form a environment not easy living for bacteria on the surface of bamboo product to achieve the antibacterial effect.

At the same time, because after carbonization the bamboo will be more hard than ordinary paper products, preventing wearing and bamboo thorn problem.

Carbonized bamboo knife seat quantity：

Safety, health, bright color，durable，the everyday necessary good products

Anti-mildew change，anti moth

Environmental protection，no crack，no decay

Q:The rotary tool holder is marked with the knife number. How to define the knife number?: If you put the first row of knives when the address to the address of the first address, you can use T0101 to call your first row of knives, you can also use T0201 to call your first row of knives. So the first four digits in the back of the T in the number of knives on behalf of the address is not in the row of practical significance. After using the knife to determine the use of the knife.

Q:However, No. 2, No. 3, the normal use of potential energy on the knife No. 4 can not be normal use of the rotation has not stopped on the 1.: Holzer component position (open the top cover can be seen as commonly referred to as the disk) is not right or damaged. Has not been able to stop because of the knife can not find the signal in place 4.

Q:To the signal line where the pull resistance, pull resistance to do with the trouble to say clearly?: In a word: your signal circuit IC no internal resistance, protection. Pull the signal is determined by a high resistance resistor at the high level, while the resistance from the current limit, pull the same. Pull on the device is the injection current, the output current is down; just pull the weak and strong resistance, no strict distinction between what; for non (collector or drain) open circuit output circuit (such as gates) current and voltage capacity improvement is limited, the pull-up resistor is the main function of open circuit output type of circuit output current for the collector channel. All the pull-down resistor pull-up resistor is used in logic circuit, the circuit current is very small, the logic circuit of MOS tube bias current is microampere, even pA uA, the current level to provide a desired level, such as the current level without any output, because there is a pullup resistor so after a level is actually connected to a high level. Power amplifier circuit with no pull down resistor. Pull the signal is determined by a high resistance resistor at the high level, while the resistance from the current limit, pull the same. The pull-up resistor is the main function of the open circuit output current output channel for the collector; main function is connected with the pull-down resistor resistor together to line in the closed circuit driver (node) to a fixed level. Pull on the device is the injection current, the output current is down to note is that the pull-up resistance caused by too large delay output level, including the choice of the principle of resistance: 1, from the current irrigation ability to save the power consumption and chip considerations should be large enough; resistance...

Q:Where are the Holzer elements in the CNC turret?: Holzer components in the tool holder is called a disk. I have a detailed look at the space

Q:How can we remove the NC turret: The first part of the rotation, two screws in the middle of the release, and then lock the 12 release of the knife rest, remember there are still under the four, in the middle of the road there is a flexible adjustment of the long screws

Q:CNC lathe tool holder clamping bit how to clip: The drill chuck can be arranged on the knife tower only by processing a drill handle, and a straight shank drill is arranged on the drill chuck.

Q:The direction of the tool head and the tool head of the NC lathe: G41g42 use the judgment of the tool tip is not the same as you this figure to 09 knife point for the center of the rotation of 180 degrees is the rear tool head position input value evaluation standard front and rear is the same as the input value

Q:What are the reasons for the deviation of the CNC lathe tool holder after each turn: The mechanical structure of the cutter head is damaged, the parts can be replaced, but the new tool holder is recommended. Because the replacement of mechanical parts is also difficult to ensure accuracy, it is best to change the tool holder.

Q:CNC lathe turret and turret turret that good: First of all, to meet your needs, such as1) you are the object of processing, a fixture may be used to the maximum number of tools, if it is possible to more than four, then the square knife is not appropriate.2) you do not work in the workpiece, drill, tap a class of tools. Or a tail frame, and the tail can be installed on the drill bits and other tools, then you can consider the use of square knife.3) frame structure, different cutter positioning form different tool installation precision, repeated installation accuracy, with the knife and machine are different, if you have this requirement, in the choice of when it is necessary to consider the.

Q:CNC turret can be turned into 45 degrees ah? Can you turn counterclockwise?: Numerical control machine tool holder can be numerically controlled turret also has an electric, hydraulic knife. CNC turret and part of the NC cutter can turn 45 degrees and counter clockwise. Part of the electric, hydraulic tool holder can not turn counterclockwise.

1. Manufacturer Overview
Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates
a) Certification Name
Range
Reference
Validity Period

3. Manufacturer Capability
a)Trade Capacity
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range