knife seat,F-KB031 Rubber wood knife seat,your best choice
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
product name:rubber wood knife seat
material:rubber wood
N.W.:1.35kg
MEAS:22*19*10cm
Specifications:
Has the quite distinct shape of the mountain wood grain, and the contact surface is a good sense
Excellent toughness, process into various curved according to the needs , full of beauty
Solid texture,manufactured goods with firm structure,prolonged service life
The texture of rubber wood is fine and closely woven,pore full of lots ot padding so it's hard to absorb water and corrode.
Description:
1、The knife seat use material of high quality natural rubber wood and take professional advanced machine equipment and manual binding.
2、The knife seat was refined by material, assembly, polishing, painting and other procedures.
3、The knife holder has the advantages of real materials, excellent workmanship, mouldproof and moth proofing, anti bacteria, wear-resisting etc.
4、Hoteam commerce co.,LTD,is a manufactory specialized in all kinds of wood knife handles,wood seats,chopping boards and other woodworks.
5、Because the knife tool contact with tool wet food for long time, is very easy to breed bacteria, you should ensure that dry and clean and put it in the open air
- Q:CNC turret is also called the sender sensor
- It can be said that the signal is used to change the knife
- Q:For what parts of the process, what is the difference between the installation
- The central frame is mainly used for supporting and fixing the shaft parts or strengthening the rigidity.The difference is: the 1 position is different; the center frame of the 2 does not move with the carriage.
- Q:CNC lathe tool holder four and six stations which good
- The internal structure of the turret principle is similar, but the four station looks like car carriage, six station is a brick tower structure, slightly larger, a fixture of processing content more, six station processing large size parts, the adjacent knife knife may interfere with the four station, six station four station your. Think about it.
- Q:CNC lathe turret in place how to do
- CNC turret repair more complex (personally think), I suggest you find professionals to repair
- Q:Why is the number 980 CNC lathe turret always turn and then alarm
- Tool holder is always unable to find the knife position, usually 24 or 0 volts knife restIf it is a station can not find the detection switch is broken
- Q:CNC lathe tool holder clamping bit how to clip
- The drill chuck can be arranged on the knife tower only by processing a drill handle, and a straight shank drill is arranged on the drill chuck.
- Q:What is the function of the tool on the turret of NC lathe?
- The angle of the adjusting tool post is only temporary change, and the position of the tool post can be repeatedly positioned after the rotation of the tool holder!
- Q:How to install CNC machine tool
- You should first look at what products and processing process can be determined by what what tool, with a few knives, then you can choose to install the tool; we should consider the tool do not interfere in the process, should pay attention to the length of cutting machining depth and the selected is appropriate, but also note is the tip and selection tool the height of the knife is to be consistent, high attention to; such as your machine tool clamping position width is 64.0mm, then you must choose the cutter bar is 32.0mm, or the center of your nose is not high, so the processing will have a lot of problems; or you can according to the side making auxiliary tool carrier the installation is generally use screws; the cutter bar top dead on it
- Q:How to distinguish the CNC lathe turret and turret turret after that car, belonging to the front tool or tool? Before the turret is cylindrical with G42 or inner circle?
- Whether NC or normal car, a knife in the side is the pre processor, or post, either rear or front, when processing with radius compensation are determined according to the post, the outer circle with G42, G41 in the hole.
- Q:The first reason is that the cutter shaft of the motor shaft is broken for a shaft / how long it will not be able to die!
- This problem is very simple, is not the command input, motor rotation, and the knife is like a rotation and stuck? This is just a tool conversion timeout, unscrew cap above the turret, turret removed, which has four pins, take out to see if bent, or flash, with the change of the pin, the pin can be used for standard parts can be, can not find it on 4mm head cut tail can be loaded
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
knife seat,F-KB031 Rubber wood knife seat,your best choice
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Hot Searches
Related keywords