Mould Spring with free design
- Loading Port:
- Ning Bo
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1000Pieces pc
- Supply Capability:
- 100000 Pieces per Month pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
The Specifications of The Mould Springs
Product Name | Compression mould spring | Supply Ability | 900000000PCS | ||
Wire diameter | 0.08mm~10.0mm | Type of shipping | By sea/air/DHL/Fedex/UPS etc | ||
Quality certification | ISO9001:2008.SGS,the French | Payment term | L/C,T/T,D/A,D/P,Western union,Money Gram,Paypal | ||
BV authentications | |||||
The scale of Hershey spring | About 6000 suqare meters | Employee numbers | About 100.and our group are becoming larger | ||
Industry Experience | Over 21 years' experience in the spring industry. |
Mould Spring Production and Manufacturing
1.Our engineers are eager to help provide the most dependable mould
spring for your applications. Our company is a mould spring
manufacturer that you can depend on to deliver high quality mould
spring with speedy lead times
2.Specialiaze in mould spring .your inquiries will get prompt reponse
within 24 hours.
3.Free design all kind of non-standard mould spring as you requested.
4.Specification: 6X10mm ---70X500mm
5.Paint:environmental protection electrophore
Mould Spring:Use of attention for mould spring
Choose right mould spring or will distortion and reduce service life.
Can’t have gap between upper plate and mould spring or will distortion and rupture.
When free length of moudl spring is 4 times to outer diameter ,please use guide rod shield to protect service life.
Can't use it for anything except compression .
Please use it on the mould.
When the lower plate parallelism is not well, high stress will happen and cause transformation and rupture .
It must be have some preloading when put mould spring on the mould . preventing mould Bear impact load and cause fatigue damage.
Install and valid service condition
>When Coil Spring install the hole of bottom without leader ,the deep of hole must be more than two rings than mould springs.
>when mould spring install with leader ,length of leader must be higher than length of mould spring
>.Close state (stroke limit) is reference dimension ,Pls do not use if more than 300000 times or it will be bending and failure.
>When installing, preloading is one over ten or more of the compression. When cope plate use with gap .will cause mould spring bending or scrap.
Service condition:
1. Allowed temperature range for mould spring
TF.TL.TM.TH.TB.TR.TY : 80°C--30°C
Higher than these temperature ,you should customize.
In practice,when temperature higher than above. Mould spring will be scrap ,bending and etc. or use based on technicist’s guide .
2.Don’t use mould spring on high temperature and wet ,or mould spring will be scrap ,bending and rustiness.
Packaging and Transportation
Our factory of Mould Springs
- Q:I buy a spring made of 1.2mm steel wire from a hardware store that needs quenching
- Spring: Spring quenching hardening is the steel is heated to the critical temperature of Ac, or Ac: the above heat preservation time, the austenite with greater than the critical cooling rate of rapid cooling, so as to obtain the heat treatment method of martensite.
- Q:What are the categories of springs?
- A spring is a mechanical part that uses elasticity to work. Parts made of elastic materials deform under external force and are restored to original shape after removal of external forces. Also made as a spring". Usually made of spring steel. The type of spring is complex and varied. According to the shape, there are mainly spiral spring, scroll spring, plate spring, special-shaped spring and so on.
- Q:Can springs be used for support?
- The following individual ideas do not represent the bestFriction is bound to damage,Gaskets can be used to prevent direct friction between the spring and gear to lubricate, optimize wear and prolong life.
- Q:How to process Spring Steel
- After the spring is made, shot peening can produce residual compressive stress on the surface of the spring so as to offset part of the working stress on the surface layer and restrain the formation of surface cracks, which can significantly improve the fatigue limit of the spring.
- Q:Stainless steel and spring steel hardness, who is hard?
- To sell the spring steel where seen relatively hard two pliers are very difficult to open
- Q:Spring dynamometer and spring balance what is the difference
- Spring dynamometer is a force measuring spring balance is to measure the quality of
- Q:Cold rolled coil spring spring and difference "
- The main production process is different, the compression spring as an example:The typical process of coil spring: blanking - end processing (rolled or forged flat) - heating - - - quenching - tempering spring roll grinding end - compressor (load - Test), shot peening (cleaning) - coating.Cold roll spring does not require heat treatment of material roll, point line process: rolling, annealing, stress to both ends of the surface grinding, (blast), (the whole school), (BKS), standing or forcing treatment, surface inspection and treatment.Coil spring is mainly used for rolling large spring, heating easily after twisting forming, springback is smaller, molding after quenching and tempering treatment.The cold coiling spring is directly coiled with spring steel wire, and the resilience is greater, and the winding tools need to consider the springback compensation amount and roll into the direct tempering process.
- Q:Hydraulic diagram of the one-way valve has two kinds of drawing, with a spring, without a spring, what is the difference between automatic reset function is not? Without a spring, it will not be repeated
- The simplified method of drawing without springs is the same
- Q:In short, in vibration and wave, it is not easy to make mistakes when we grasp the difference and relationship between "displacement" and "displacement relative to the balance position"
- In short, in vibration and wave, it is not easy to make mistakes when we grasp the difference and relationship between "displacement" and "displacement relative to the balance position"
- Q:What kind of material does spring have?
- 65MnSpring steel belongs to the mechanical structure steel; according to the quality grade, it belongs to the special quality steel, that is to say, in the process of production, it is necessary to strictly control the quality and performance of the steel.
1. Manufacturer Overview |
|
---|---|
Location | Suzhou, China |
Year Established | 2001 |
Annual Output Value | more than US$ 5 Million |
Main Markets | North America, South America, Eastern Europe, Southeast Asia, Africa, Mid East, Eastern Asia, Western Europe |
Company Certifications | ISO/TS 16949; ISO 9001:2008 |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | Shanghai |
Export Percentage | 41% - 50% |
No.of Employees in Trade Department | About 170 People |
Language Spoken: | English; Chinese; |
b)Factory Information | |
Factory Size: | About 35,000 square meters |
No. of Production Lines | |
Contract Manufacturing | OEM Service Offered; Design Service Offered |
Product Price Range | High; Average |
Send your message to us
Mould Spring with free design
- Loading Port:
- Ning Bo
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1000Pieces pc
- Supply Capability:
- 100000 Pieces per Month pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Hot Searches
Related keywords