Made in China Excellent Performance Graphite Electrode for EAF Furnace Very Good Quality
- Loading Port:
- Qingdao
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 10 m.t.
- Supply Capability:
- 1000 m.t./month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
High Quality Graphite Electrode For EAF Furnace
Packaging Details:
1: Wooden crates with steel straps; wooden crates treated with "IPPC" label
2: standard export fumigated wooden box with steel strip fixed outside
3: In wooden case, each nipple must be packed in cardboard box.
Each electrode and nipple to preset at one end. The head of the preset nipple shall be covered by cardboard cap supported by wooden plate from both ends to avoid damage to the threads during transportation
Delivery Detail: 15-45 days after confirming the contract
Production Description:
Graphite electrode is made from the domestic first petroleum coke and high quality needle coke and widely used in the electric arc furnaces for production of alloy steels, metal and other nonmetallic materials, etc. The graphite electrodes include regular power, high power, super high power, ultra high power and square electrode. The range of diameters covers from 200mm to 700mm. Our products own the following characteristics: low electric resistance, good electric and thermal conductivity, high oxidation resistance, greater resistance to thermal and mechanical shock, high mechanical strength, high machining accuracy.
Physical and chemical index
Item | Unit | Nominal Diameter(mm) | |||
YB/T4088-2000 Industry Standard | Typical Values | ||||
300-400 | 450-550 | 350-550 | |||
Resistance | Electrode | ohm | ≤6.2 | ≤6.5 | 4.6-6.2 |
Nipple | ≤5.5 | ≤5.5 | 3.5-4.5 | ||
Bending Strength | Electrode | Mpa | ≥10.5 | ≥10.0 | ≥11.0 |
Nipple | ≥16.0 | ≥16.0 | ≥18.0 | ||
Elastic Modulus | Electrode | Gpa | ≤14.0 | ≤14.0 | ≤13.0 |
Nipple | ≤18.0 | ≤18.0 | ≤17.0 | ||
Density | Electrode | g/cm3 | ≥1.65 | ≥1.64 | 1.65-1.72 |
Nipple | ≥1.72 | ≥1.70 | 1.75-1.82 | ||
Ash content | Electrode | % | ≤0.3 | ≤0.3 | ≤0.3 |
Nipple | |||||
CTE(100-600) | Electrode | 10-6/C | ≤1.5 | ≤1.5 | 1.20-1.40 |
Nipple | ≤1.4 | ≤1.4 | 1.10-1.30 |
- Q:Iron and graphite as electrodes and Nacl as electrolyte solutions. Why do they produce electric current? Graphite and iron react not with solution, can they be connected by wires?
- What happens is oxygen etching negative pole: Fe-2e-=Fe2+ positive electrode: O2+2H2O+4e-=4OH-, of course, the current is produced.
- Q:Electrolytic water solution, two electrodes are graphite electrode, the negative electrode can produce large amounts of hydrogen, the anode does not produce half of oxygen, and only a small amount of it?
- The oxygen will react with the graphite and the gas will dissolve.The iron has been oxidized.
- Q:The production of one ton of steel required graphite electrode
- Can not generally say, a ton of steel production consumes much of graphite electrode.
- Q:Jiqiu conductive graphite electrode, how to compare with copper is relatively large resistance value?
- This is not a good estimate of the sheet graphite resistance after 5mm
- Q:What do carbon products include?
- High power electrode and ultra high power electrode. The carbon block can be divided into blast furnace carbon block, aluminum carbon block and electric furnace block. Carbon products can be divided into carbon products, graphite products, carbon fibers and graphite fibers according to the depth of processing. Carbon products can be divided into graphite products, carbon products, carbon fibers and special graphite products according to the raw materials and the production process. Carbon products according to their ash content, and can be divided into multi gray products and less ash products (including ash below l%).
- Q:How long is the graphite electrode machining cycle?
- Industrial graphite is hard and brittle, and the tool is worn more seriously during machining. It is generally recommended to use carbide or diamond coated cutting tools. When the graphite is rough, the cutter can be directly worked on the workpiece. When it is finished, it is necessary to use light knife to walk quickly to avoid the occurrence of chipping and chipping
- Q:What are the factors that affect the electrode wear rate of machine tools?
- Effect of processing voltage on electrode wear. The processing voltage is the average voltage between the discharge time and the gap. When the voltage is lower than the power supply voltage (voltage) 25%, electrode loss will increase, which is due to the electrode and the workpiece is too close, the discharge column energy is too large, the electrodes generate heat radiation is too strong, at the same time, there are a large number of continuous arc discharge. But the working voltage is too high (partial load processing), bad conditions of thermal effect in the gap, is not conducive to the adsorption of copper electrode of carbon graphite, destroy the covering effect. Similarly, the electrode loss increase, therefore, corresponding to different processing standards should be selected to adjust the discharging gap voltage.
- Q:National standard for graphite electrodes
- The national standard normal power graphite electrode graphite electrode: the standard name standard classification number Q51 Standard No. YB/T 4088-2000 for YB/T 4088-2000 YB/T 4088-1992 2000/12/1, instead of the execution time of 0:00:00 release time 2000/7/26 0:00:00 adoption situation
- Q:Why use platinum ferroalloy instead of iron as electrode?
- General industrial grade silicon dioxide, because the preparation technology is different, can be divided into two types, one is dry, sintered (Fume Type), a wet precipitation type (Precipitated Type), and two of the surface area, the surface with hydroxyl (-OH) are the same, in general, the former the latter is more, less, the two surface has the tendency of hydrophilic, as for lipophilic polymer, such as paint, rubber... Etc.,... If the silica surface pre rendered hydrophobic, has a good effect.
- Q:Graphitized coke, graphite, broken, mixed up, how to export?
- The graphite powder is soft, black and gray, greasy and polluting paper. Hardness is 1~2, along the vertical direction with the increase of impurities, its hardness can be increased to 3~5. The specific gravity is 1.9 ~ 2.3. Under isolated oxygen conditions, the melting point is above 3000 degrees Celsius and is one of the most refractory minerals. At room temperature, the chemical properties of stone toner are relatively stable, insoluble in water, dilute acid, dilute alkali and organic solvents. The material has high temperature resistance and conductivity, and can be used as refractory materials, conductive materials, wear-resistant and lubricating materials.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Made in China Excellent Performance Graphite Electrode for EAF Furnace Very Good Quality
- Loading Port:
- Qingdao
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 10 m.t.
- Supply Capability:
- 1000 m.t./month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products