Vehicle side wall aluminum profile
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
We are the largest aluminum profilemanufacture in
Material | Alloy Aluminum 6063,6061,6005,6082 or customer nominated |
Temper | T3, T4, T5, T6 and other |
Surface | Anodize, electrophoresis, Mill,etc |
Colour | -- |
Length | Not more than 16 meters |
Good Package | Inner plastic film /outside carton/wooden pallets |
Payment Method | T/T, L/C, etc |
Delivery Time | Normally 2-4 weeks, Delivery time can be consulted. |
Press Machine | 500-12500 tons all together 93 press lines. |
Fabrication | 1. Car body; 2. Drilling; 3. Bending; 4. Cutting; 5. etc. |
Certificate | ISO/TS 16949,DNV,IRIS,CCS,AFA,etc. |
Dies | 1. Using our dies, no fee; |
2. Using customer drawing, opening dies, usually about 5~50 tons then the dies cost can be refunded. | |
3. Die cost is negotiable base on the order quantity | |
Capability | Annual output 800,000 tons |
- Q:Is the air conditioner aluminum tube or copper tube?
- Copper, of course. Copper has shrinkage, ductility, and high prices
- Q:How to distinguish between copper tube or aluminum pipe?
- If it is not installed, weighing, the copper tube is much heavier than the aluminum tube. There is opened the insulation pipe joint at 10 cm behind the place if there are traces of welding pipe, and the outside layer of plastic sheath wrapped, if it is, if not sure is aluminum, copper can be easily resolved. After installation, the air conditioner is only identified by the latter method.
- Q:Can you tell me what kind of pipe bender is used to bend the aluminum tube? It's not easy to wrinkle or break
- This is actually very simple, that is, change the processing methods, first of all: do not wear mandrel tube bender, to avoid the mandrel in the bend when the friction aluminum tube, so that the material after the wound, it is easy to break!
- Q:Do aluminum pipes require insulation?
- Yes, aluminum pipes generally require insulation to prevent heat transfer, condensation, and energy loss.
- Q:How to weld aluminium pipe
- 3, WE53 low temperature aluminum strip for Aluminum Alloy 7 series of welding, welding temperature in 380-400 degrees, the advantage of welding does not need any auxiliary welding flux, thus preventing some residual flux in the process of welding, and the welding strength is very high, can solve the 3 line Aluminum Alloy and castings. Die casting or welding.
- Q:Is GREE a brass tube or an aluminum tube?
- What flows inside is a refrigerant. It must be a copper tube!
- Q:6063, how to prevent cracking aluminum tube, variant manual bending machine bending machine bending, what should pay attention to?No one knows?
- 6063, aluminum tube plasticity is very good, if you want to bend, it is recommended to return the fire, reduce the hardness, bending after quenching, bend pipe bend can be.
- Q:When I repair the refrigerator, I often encounter leakage in the aluminum pipe. It can not be repaired by conventional wind welding. What is the best way to repair it?
- Cut off at the point of leakage, with a copper knot to connect the head, you should pay attention not to force too much.Now the refrigerator tube is the use of aluminum tube or Bondi tube (Bondi tube, that is galvanized steel pipe, in fact, iron pipe, iron pipe above the paint once lost, it is easy to rust. )The aluminum pipe is more corrosion resistant than the iron tube, and the iron pipe is not corrosion resistant. In fact, the best or copper pipe, but now no manufacturers have produced, mainly or cost.
- Q:Are aluminum pipes suitable for potable water systems?
- Yes, aluminum pipes can be suitable for potable water systems. Aluminum is a lightweight and corrosion-resistant material that can provide a durable and long-lasting solution for transporting potable water. It is commonly used in plumbing systems, including for both hot and cold water applications. Aluminum pipes are known for their high strength-to-weight ratio, which makes them easy to install and transport. Additionally, aluminum has a low reactivity with water, meaning it does not easily leach harmful substances into the water supply. However, it is important to note that aluminum pipes should be properly coated or lined to prevent any potential reactions with the water, as uncoated aluminum may release small amounts of aluminum ions into the water. Overall, with the proper coating or lining, aluminum pipes can be a suitable and safe choice for potable water systems.
- Q:Can aluminum pipes be used in HVAC systems?
- Indeed, HVAC systems can make use of aluminum pipes. Aluminum, being a metal that is both lightweight and resistant to corrosion, is an optimal selection for HVAC purposes. These pipes find common application in air conditioning and refrigeration systems, as well as in heat exchangers and condensers. Their exceptional thermal conductivity facilitates efficient heat transfer, and they possess durability and longevity. Moreover, aluminum pipes are easily manipulated to meet specific requirements, as they can be readily cut, bent, and shaped. All in all, aluminum pipes present a dependable and economical choice for HVAC systems.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Vehicle side wall aluminum profile
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords