Warehouse Light Fixtures
Warehouse Light Fixtures Related Searches
Led Light Bulbs For Ceiling Fixtures Led Lamps For Ceiling 42 In Ceiling Fan With Light Parts For Light Fixtures Light Projector For Christmas Grill With Led Light Bar Hanging Lights For Kitchen Bar Ceiling Lights For Sitting Room Ceiling Brackets For Lights Ceiling With Led LightsHot Searches
Price For Stainless Steel Scrap Scrap Price For Stainless Steel Price For Stainless Steel Price Of Shipping Containers For Sale Stock Price For Aluminum Air Pump For Aquarium Price Used Foam Board Insulation For Sale Bags Of Cement For Sale Types Of Temporary Side Panels For Cement Deck Magnesium Oxide Board For Sale Hdf Board For Sale sintra board for sale Solar With Inverter Price Pedestal Fan With Water Spray Price Price Of Scrap Stainless Steel Price Of Stainless Steel Scrap Price Of Stainless Steel High Mast Light Price List Solar High Mast Light Specification Used Foam Board Insulation For SaleWarehouse Light Fixtures Supplier & Manufacturer from China
Okorder.com is a professional Warehouse Light Fixtures supplier & manufacturer, offers integrated one-stop services including real-time quoting and online cargo tracking. We are funded by CNBM Group, a Fortune 500 enterprise and the largest Warehouse Light Fixtures firm in China.Hot Products
FAQ
- Patch LED light does not flash, why?
- Are you saying that lamp is flashing? You can check the power output, according to your standard parameters and SMD beads, lamp panel series parallel mode, calculate the power output to output power of the test, you may be wrong, power, overload, but also the effective part of you may be the circuit for power transmission is not stable or low
- Patch LED features
- The principle of luminescence is that of cold luminescence, not by heating or discharging light, so the component life is about 50~100 times longer than that of tungsten filament bulb, and about one hundred thousand hours.
- What is patch SMD-LED?
- SMD LED is the surface mount light emitting diode. It is a solid state semiconductor device that converts electricity directly into light. The heart of LED is a semiconductor wafer, one end of which is attached to a bracket, one end is negative, and the other is connected to the positive electrode of the power to encapsulate the entire wafer with epoxy resin.
- What should I notice when I want to solder 1206 LED patch type luminous tube on fine copper wire?,
- I recommend reflow soldering under normal conditions and manual welding only when repaired. 2 manual soldering electric soldering iron maximum power can not exceed 30W, welding temperature is controlled within 300 degrees, welding time less than 3 seconds. 3 do not touch the colloidal iron welding head. 4 when the pin is heated to 85 degrees centigrade or higher than this temperature, it can not be pressed. Otherwise, the welding will be broken.
- What is the principle used in SMD LED lamp, should pay attention to what the problem?
- LED installation method 1, don't install the LED pin in 2, under the condition of deformation in printed circuit board when installing LED, circuit board hole center distance and LED pin center spacing should be the same, if the hole spacing will make the lamp feet have residual stress and welding...
- What is the difference between SMT LED packaging with silicone and epoxy resin transparent package? What is the market situation of these two types of packaging?
- At present, it is basically made of silica gel, and the epoxy resin is very few. Only those with lower price may use some. Why is it rare to use epoxy? Because of the use of LED epoxy patch cited some discomfort because the cable used in the above: reflow welding, high temperature resistant epoxy epoxy and silicone not lead to separation, produce decay dead lights etc..
- Patch LED light broken one, short circuit can use it?
- Can not casually short-circuit, according to the LED connection, but also to see the power supply voltage and current, all the LED can not flow. Any short circuit may cause excess LED to flow over or over, causing a chain reaction, a bad string,...... .
- LED patch lamp band, how to calculate how many watts a meter, such as 3528-60 beads is how much?
- 3528 single lamp is 0.06W 0.06*60 lamp =3.6W 3528-60 bead is 3.6W/ meters
