Drilling Tools Best Quality Button Bits Top Hammer Rock Drilling Tools
- Ref Price:
-
- Loading Port:
- Qingdao
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 50 pc
- Supply Capability:
- 10000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Specifications of Hammer Rock Drilling Tools
Top Hammer Rock Tool:
- Thread connection: R22, R25, R28, R32, R38, T38, T45, T51;
- Including button bits,drill rod,coupling.
About products:
- Integral drill steels (Integral Drill Rods)
Shank H22x108mm, H19x108mm, standard hex. Bit diameters include 20-42mm.
- Tapered drilling tools (Tapered Drill Steel)
Including:Shank H22x 108mm, (6, 7, 11, 12 degree taper) taper rods in most lengths.
A comprehensive range of button bits, cross bits and chisel bits with (6, 7, 11, 12 degree taper).
Bit diameter: 28mm-57mm.
- Extension drilling tools
Button bit, face design: Flat face, drop centre, Normal and Retrac body.
Tungsten carbide (Buttons): Spherical, ballistic and Conical. (Threaded R32, R38, T38, T45, T51, bit diameter: 45mm-127mm);
Couplings sleeves-manufactured with a middle stop to prevent walking along the thread. Include couplings sleeve (threaded R22, R25, R28, R32, R38, T38, T45, T51)
Shank adaptors-carburized and manufactured with tight tolerances and controlled straightness.
- Down the hole hammers and DTH bits (Down The Hole Drilling)
Offer IR hammer, DHD3.5, DHD340a, DHD360, DHD380, and low pressure hammers CIR65a, CIR90, CIR110, CIR150, CIR170 etc.
DTH bits: 60mm-254mm bits with flat face, concave design fit for the atlas copco and ingersoll-rand model etc.
- Excavate coal cutter bits
Include all kinds of round cutter bit and flat cutter bits for excavate coal machine as the replacements of kennametal. Such as U76, U82, U84, U85, U92, U94, U95, U118 and coal bolting bit and coal bolting rod.
- All kinds of casing bits for shield machine and construction tools.
- Round road planning bit for road milling machine and machine.
Shank diameter=19.4mm, 25mm, 30mm, 33mm, 38mm, etc.
- Blast furnace tap hole drill tools. (Rod, Cross bits, button bits and X-type bits etc).
- Q:How do you grind the diamond tool?
- Before grinding, diamond powder is first mixed with olive oil or other similar material into a paste, then coated on the surface grinding disc, placed a period of time to paste into fully cast iron pore grinding disc, with a large diamond in grinding disc surface of pre grinding back and forth, to further strengthen the role of Mosaic diamond powder in cast iron pore. In the case of grinding, the grinding diamonds are usually buried in a tin bucket, showing only the grinding surface.
- Q:How do you divide the main cutting edge of the blade after the main of the tool?
- The blade of the knife that flows through the blade. (2) the face of the knife and the workpiece are on the surface of the surface of the machined surface (transition surface). (3) the surface of the knife face and the surface of the machined workpiece.
- Q:Method of installation of CNC internal turning tool
- You've got the wrong knife. Here's the solution: Sharpen the position of the screw in a small plane with the wheel
- Q:What does the color stand behind the car knife?
- Sorry, no research on this.I hope my answer will help you.
- Q:How do you sharpen a cast-iron tool?
- The tool should be chosen well, at least with YG6, the fine car is YG3. 2) the car knife takes the Angle of 0, the big cut open the rough and the negative Angle. The big round lone blade.
- Q:How to weld a car knife? How do you handle the welding fire
- Feel blade and knife block joint red can welding, brazing welding car, estimate principle also about, don't just blowing the knife block, study suggest or practice.
- Q:Hello, I ask you a question, how much of an Angle will you wear with a white steel knife?
- Speed is too high to copper don't hit such a high speed car ~ can't add cutting fluid to high speed machining copper knife grinding hard ~ hot knife fast easy to wear, you wear white steel knife to sharpen some additionally, feed is generally based on material and rotating speed, but have a roughly the speed, the iron material generally around 100-800, around 700-800 in copper and aluminum has the highest speed, 2000 turn can, cast iron in 100-300 turn around, the adjustment of the feeding speed is the speed and feed rate ~ are generally from experience, I do the lathe work more than 4 years, how much I haven't seen feeding speed, only know a living and feed quantity and speed. Copper can be a little bit bigger, but the knife is worn as short as possible, if I give you a knife in your 20 minutes
- Q:How many degrees are used in the car knife
- The car knife is the same as the tip of the outside of the car, but there is a circular fixture on the small towed board!
- Q:How many lathe knives are there?
- The advantage of indexable tool Compared to the welding tool, the indexable turning tool has the following advantages: (1) the knives' service life Due to the blade to avoid the defects caused by high temperature welding and grinding, cutting tool geometry parameter entirely by the blade and tool holder slot assurance, cutting performance is stable, so as to improve the tool life. The production efficiency is high because the machine operator no longer sharpens the knife, can greatly reduce the auxiliary time such as the stop changing knife. (3) it is helpful to promote new technology and new technology, which can be used to promote the use of new tool materials such as coating and ceramics. (4) to reduce the cost of cutting tools Because of the tool rod service life is long, greatly reduce the consumption of the tool holder and inventory, simplified the tool management, reduce the tool cost.
- Q:How to sharpen the cut of the lathe
- The position and method of sharpening the tool People stand on the side of the grinder to prevent debris from hurtful when the grinding wheel breaks. 2, the distance between the two hands is relaxed, the two elbows tighten the waist, in order to reduce the shaking of the sharpener. 3, grinding, turning to on the plane of grinding wheel center, a turned-up nose about 3 ° ~ 8 °, after turning tool grinding wheel contact should be done about the horizontal direction of movement. When the tool leaves the wheel, the knife must be lifted up to prevent the blade from being hurt by the grinding wheel. 4, in the face of the machete, the tail of the dao is left over the Angle of the main Angle. When the side of the knife is worn, the end of the pole is angled to the right. When grinding the tip of a knife, it is usually used to hold the front of the turning point with the left hand and turn the back of the tool with the right hand.
1. Manufacturer Overview |
|
|---|---|
| Location | |
| Year Established | |
| Annual Output Value | |
| Main Markets | |
| Company Certifications | |
2. Manufacturer Certificates |
|
|---|---|
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period | |
3. Manufacturer Capability |
|
|---|---|
| a)Trade Capacity | |
| Nearest Port | |
| Export Percentage | |
| No.of Employees in Trade Department | |
| Language Spoken: | |
| b)Factory Information | |
| Factory Size: | |
| No. of Production Lines | |
| Contract Manufacturing | |
| Product Price Range | |
Send your message to us
Drilling Tools Best Quality Button Bits Top Hammer Rock Drilling Tools
- Ref Price:
-
- Loading Port:
- Qingdao
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 50 pc
- Supply Capability:
- 10000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Hot Searches
Related keywords
